fping简介及使用方法
2021-10-18 9:28:33
by 山阴客

打印???
天盟网(http://www.aksky.com)
技术文章(http://www.aksky.comhref=category.php?cid=1)
LINUX文章(http://www.aksky.comhref=category.php?cid=3)

fping简介及使用方法

fping命令的官网为:http://fping.org/ 
历史版本下载地址:http://fping.org/dist/ 
第一步:安装。
wget http://fping.org/dist/fping-5.0.tar.gz
tar -xzvf fping-5.0.tar.gz 
cd fping-5.0

./configure --prefix=/usr/local/fping #指定安装路径


make

make install


安装完成
配置一下环境变量

> vim /etc/profile
export PATH=$PATH:/usr/local/fping/sbin
> source /etc/profile
> fping -v #测试下是否成功


安装成功之后输入fping -h查看帮助文档。

第二步:使用分享

fping -g ip1  ip2  

-g是ping某个pi段之间是否可达,比如fping -g 100.101.10.100 100.101.10.200 

如下图:

 

也可以通过掩码来写:如fping -g 100.101.10.1/24 

有时候也可以再加一个参数-a  即  如fping -a -g 100.101.10.1/24  这样可以直接显示可达的

帮助文件

常用: fping -Asg 192.168.1.0/24  #以IP显示是否在线,并打印出报告

Usage(用法): fping [选项] [目标...]

-a    显示目标地址是否在线
-A    以IP地址显示,并判断是否在线
-b n   发送ping的数据包量,以字节为单位 (默认 56),n写成数量,以下参数同此
-B f    设置指数回退因素为f
-c n   计算要发送到每个目标的ping信号 (默认发送 1 个包)
-C n  功能同-c,报告结果更详细
-D   在每个输出行打印时间戳
-e   显示返回包的运行时间
-f file 从文件中读取目标列表 ( - means stdin) (only if no -g specified)

-g    生成目标列表 (only if no -f specified)
    (在目标列表中指定开始和结束IP, 或者提供一个IP网络掩码)
    (ex. fping -g 192.168.1.0 192.168.1.255 or fping -g 192.168.1.0/24)

-H n   设置IP TTL值(Time To Live hops)
-i n    发送ping包之间的间隔 (in millisec毫秒) (default 25)
-I     如果绑定到特定接口
-l     loop sending pings forever永不
-m   ping目标主机上的多个接口
-M   设置Don't Fragment标志
-n    按名称显示目标 (-d is equivalent等效的)
-N   为网络数据输出兼容(-l -Q are required必须的)
-o   显示累计停机时间 (lost packets * packet interval 间隔)
-O n  在ICMP包上设置服务类型(tos)标志

-p n   ping包到一个目标之间的间隔 (in millisec)
    (in looping and counting modes, default 1000)

-q    安静模式 (don't show per-target/per-ping results)
-Q n   功能如同 -q, 每n秒显示摘要
-r n    重复次数 (default 3)
-R    随机分组数据 (to foil阻止 link data compression压缩)
-s     打印最后的统计数据
-S    设置源地址
-t n     单个目标初始超时 (in millisec) (default 500)
-T n    忽略(for compatibility兼容性 with fping 2.4)
-u     显示目标不可达
-v     显示版本
要检查的目标列表 (if no -f specified)

 

English Version

fping 5.0

Usage: fping [options] [targets...]

Probing options:
   -4, --ipv4         only ping IPv4 addresses
   -6, --ipv6         only ping IPv6 addresses
   -b, --size=BYTES   amount of ping data to send, in bytes (default: 56)
   -B, --backoff=N    set exponential backoff factor to N (default: 1.5)
   -c, --count=N      count mode: send N pings to each target
   -f, --file=FILE    read list of targets from a file ( - means stdin)
   -g, --generate     generate target list (only if no -f specified)
                      (give start and end IP in the target list, or a CIDR addre                                                                                                                                                              ss)
                      (ex. fping -g 192.168.1.0 192.168.1.255 or fping -g 192.16                                                                                                                                                              8.1.0/24)
   -H, --ttl=N        set the IP TTL value (Time To Live hops)
   -I, --iface=IFACE  bind to a particular interface
   -l, --loop         loop mode: send pings forever
   -m, --all          use all IPs of provided hostnames (e.g. IPv4 and IPv6), us                                                                                                                                                              e with -A
   -M, --dontfrag     set the Don't Fragment flag
   -O, --tos=N        set the type of service (tos) flag on the ICMP packets
   -p, --period=MSEC  interval between ping packets to one target (in ms)
                      (in loop and count modes, default: 1000 ms)
   -r, --retry=N      number of retries (default: 3)
   -R, --random       random packet data (to foil link data compression)
   -S, --src=IP       set source address
   -t, --timeout=MSEC individual target initial timeout (default: 500 ms,
                      except with -l/-c/-C, where it's the -p period up to 2000                                                                                                                                                               ms)

Output options:
   -a, --alive        show targets that are alive
   -A, --addr         show targets by address
   -C, --vcount=N     same as -c, report results in verbose format
   -D, --timestamp    print timestamp before each output line
   -e, --elapsed      show elapsed time on return packets
   -i, --interval=MSEC  interval between sending ping packets (default: 10 ms)
   -n, --name         show targets by name (-d is equivalent)
   -N, --netdata      output compatible for netdata (-l -Q are required)
   -o, --outage       show the accumulated outage time (lost packets * packet in                                                                                                                                                              terval)
   -q, --quiet        quiet (don't show per-target/per-ping results)
   -Q, --squiet=SECS  same as -q, but show summary every n seconds
   -s, --stats        print final stats
   -u, --unreach      show targets that are unreachable
   -v, --version      show version
   -x, --reachable=N  shows if >=N hosts are reachable or not

"



Copyright © 2002-2022 http://www.aksky.com
All rights reserved.

备案号:浙ICP备17002154号-2 Powered by: myarticle.com.cn Version 1.0dev
Processed Time: 0.0016 s Querys: 4 [ Gzip Level 0 ]